RTP-500 Rubber-Tracked Placer Applications


High-production results are achieved with the versatility of the long placing conveyor. The conveyor is 35 feet (10.67 m) long and 36 inches (914 mm) wide, with 170 degree hydraulic swing, and 12 feet (3.66 m) of hydraulic elevation adjustment.




A GOMACO RTP-500 places concrete in front of a GHP-2800 paver at work on the Baltimore/Washington International Thurgood Marshall Airport in Baltimore, Maryland. A complete listing of airports that GOMACO equipment has been on can be found at www.gomaco.com/airports.




The GOMACO RTP-500 places material in a trench to fill in around a large pipeline.




The operator’s console can move to provide the operator with a panoramic view of the whole placing operation.




Placing accuracy with the discharge conveyor is accomplished with joystick control next to the operator’s chair.




The placing conveyor allows for fast and accurate material placement from the haul road, over the stringline or other obstacles, and reaches across the grade. The conveyor deflector directs the flow of concrete at the discharge end of the conveyor.




A high volume of concrete was needed to slipform this wall on this Arkansas project. End-dump trucks and an RTP-500 kept the Commander III supplied.

Read more about this project in GOMACO World 32.2.




This contractor's GOMACO RTP-500 rubber-tracked placer and two-track GP-2600 paver slipforms sugar beet pads in North Dakota.

Read more about this project in GOMACO World 39.1.


High-production variable barrier was achieved with a GOMACO RTP-500 rubber-tracked placer and 4400 barrier machine. Production averaged 600 feet (183 m) per night slipforming 76 to 78 inch (1930 to 1981 mm) tall wall over steel-cage reinforcing.

Read more about this project in GOMACO World 42.1.




This RTP-500 is placing backfill material for a water supply pipeline in Bell Gardens, California.




This RTP-500 is placing concrete on the conveyor of a GT-3600 slipforming barrier wall in St. Louis, Missouri.




This RTP-500 runs on the new pavement, off to the side of the grade, placing concrete in front of a Commander III on this project in Indiana.

Read more about this project in GOMACO World 33.2.




An RTP-500 rubber-tracked placer works from the haul road placing concrete on the grade and over preset dowel baskets.

Read more about this project in GOMACO World 37.2.




This RTP-500, equipped with heat-resistant belts, is used in the placement of asphalt on this mainline paving project in Belgium.




The GOMACO RTP-500, powered by a John Deere 6068H turbocharged diesel engine.




The RTP-500 has fast job-site mobility, with a travel speed up to 7 mph (11 kph), and an operating speed up to 110 fpm (33.5 mpm).




The hopper features a 12 inch (305 mm) hydraulic vertical adjustment to allow for variable gate height on dump trucks. The hopper/truck seal moves out for additional cleaning.





The RTP-500 has tractive power for pushing trucks and its rubber tracks go where tires do not dare.






The hydraulically folding rear conveyor minimizes the transport requirements on the RTP-500. The overall shipping length is 37.25 feet (11.35 m), width is 11.8 feet (3.6 m) with the hopper attached, 10.3 feet (3.14 m) without the hopper, and a height of 11.7 feet (3.57 m) with the conveyor folded.













For Additional Information


RTP-500 Rubber-Tracked Placer

RTP-500 Specifications

Download The RTP-500 Brochure (PDF)

Download The RCC Screed Brochure (PDF)

Download The GOMACO Full Line Brochure (PDF)

RTP-500 Information In: Deutsch - Español - Francais - Italiano